Whirlwind supplies several sizes of floor pockets
to protect and
provide access to audio, video and AC connectors.
|
FP1 and FP-2
Constructed of 11
gauge steel, the FP-1 and FP-2 permit flush installation for safe,
reliable connections. Each unit incorporates a black carpet trim
ring with a beveled edge.
Cable-clearance slots in the doors allow them to close over cables
when in use.
Interchangeable end panels are supplied with the FP-1 and FP-2. One is solid
metal which allows the user to punch or drill it to their own individual
specifications. The other is pre-punched to accept four Whirlwind XLR or TRS
jacks. The FP-1 has one interchangeable panel on one end, the FP-2 provides
panels on both ends.
The bottom plates are also removable to facilitate additional hole punching
and connector mounting. Any or all of these may be ordered custom punched and/or
loaded by Whirlwind.
The optional back boxes (FP-1BB, FP-1BB6, FP-2BB and FP-2BB6) have three sets of
knockouts on each side.
The FP-1 and FP-2 are UL-listed and CSA approved.
Nominal Outside Dimensions:
FP-1:
Box: 6 1/8" x 6 1/8" x 4"
Lid: 8" x 8"
FP-2:
Box: 12" x 6 1/8" x 4"
Lid: 14" x 8"
FP-1BB:
6" x 6" x 4"
FP-1BB6:
6" x 6" x 6"
FP-2BB:
6" x 12" x 4"
FP-2BB6:
6" x 12" x 6"
(Click
here
to view a detailed spec sheet, 361KB in PDF format.)
|
FP3 and FP-4
Whirlwind FP-3 and FP-4 units feature removable bottom and end panel(s) to
facilitate custom punching and engraving. (The FP-3 has one interchangeable
panel on one end, the FP-4 provides panels on both ends.)
Cable-clearance slots in the doors allow it to close over cables
when in use and the FP-4 features a second separate hinged section that can
remain open if the pocket is used with large diameter cable.
Both the FP-3 and FP-4 are deep enough to contain multipin connectors including
Whirlwind's MASS series.
Nominal Outside Dimensions:
FP-3:
Box: 10" x 10" x 4.5"
Lid: 12" x 12"
FP-4:
Box: 18" x 10" x 8"
Lid: 20" x 12"
Optional back boxes are available:
FP-3BB6 - for FP-3
10" x 10" x 6" deep
FP-3BB8 - for FP-3
10" x 10" x 8" deep
FP-4BB8 - for FP-4
18" x 10" x 8" deep
(Click
here
to view a detailed spec sheet, 586 in PDF format.)
|
|
FSR FLOOR POCKETS
FSR Floor Pockets
are designed to fit the needs of power, audio, video, and data
applications and provide a practical solution for cable storage while
maintaining easy access. The cover has a large, lift-off section for
access to internal cables and connector plates while a smaller trap-door
creates a cable exit. The sturdy 11 gauge cover lies flush with the
floor while the brass or aluminum edging is only partially seen through
the carpet. Two angled brackets are provided with a single, double, and
a four gang opening for connector mounting. Standard wall plates are
additional.
FL-500P
|
FL-500P
is designed for rooms with carpeted floors over concrete. The edging is
available in 1/4" or 1/2" heights. Adjustable leveling feet are included.
Box Size:
10" x 12" x 6". 4" depth available
Cover Size:
10 1/2" x 12 1/2" x 1/8"
Edging Height:
1/4" or 1/2"
Edging Material:
brass or aluminum
Knockouts:
Total of 8, either 1 or 1 1/4"
Weight:
16 pounds
FL-540P
is similar in design to the FL-500P, except it has a mounting flange
designed to drop into raised access carpeted floors.
Box Size:
10" x 12" x 6". 4" depth available
Cover Size:
11-1/2" x 13-1/2"
Edging:
1/4"
Edging Material:
brass or aluminum
Knockouts:
Total of 8, either 1 or 1-1/4"
Other FSR boxes for non-carpeted floors are available.
|
|
